Yokogawa EJA440E User Manual Page 25
- Page / 96
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
<3. Parameter Setting>
3-12
IM 01C25T01-06EN
3.2 Basic Setup
IMPORTANT
After setting and sending data with the HART
conguration tool, wait 30 seconds before
turning off the transmitter. If it is turned off
too soon, the settings will not be stored in the
transmitter.
3.2.1 Tag and Device Information
If there are specied when ordering, the desired Tag
No. and device information are set and shipped.
Tag No. and device information can be checked as
follows.
• Procedure to call up the display using by DD
and DTM (excluding EJX HART 5 DTM based
on FDT1.2)
Item Procedure
Tag [Root Menu] → Basic setup → Tag
Long tag
(HART 7 only)
[Root Menu] → Basic setup → Long
Tag
Descriptor [Root Menu] → Basic setup → Device
information → Descriptor
Message [Root Menu] → Basic setup → Device
information → Message
Date [Root Menu] → Basic setup → Device
information → Date
• Procedure to call up the display by EJX HART 5
DTM based on FDT1.2
Item Procedure
Tag Easy Setup → Tag
or Conguration → HART → Tag
Descriptor Conguration → Device information 1
→ Descriptor
Message Conguration → Device information 1
→ Message
Date Conguration → Device information 1
→ Date
When the Tag No. and device information are
changed, input them based on the following
limitations.
Item Limitations
Tag Up to 8 characters or numbers*
1
Long tag
(HART 7 only)
Up to 32 characters or numbers*
2
Descriptor Up to 16 characters or numbers*
1
Message Up to 32 characters or numbers*
1
Date mm/dd/yyyy
- mm: month (2 digits)
- dd: days (2 digits)
- yyyy: years (4 digits)
*1: The characters bounded by the thick line in the following
table can be used.
*2: All characters in the following table can be used.
SP ! " # $ % & ' ( ) * + , - . /
0 1 2 3 4 5 6 7 8 9 : ; < = > ?
@ A B C D E F G H I J K L M N O
P Q R S T U V W X Y Z [ \ ] ^ _
` a b c d e f g h i j k l m n o
p q r s t u v w x y z { | } ~
*: SP shows one-byte space
3.2.2 Unit
The unit parameter is set at the factory before
shipment if specied at the time of order. Follow the
procedure below to change the unit parameter.
• Procedure to call up the display
DD and DTM
(excluding EJX_
HART 5[1.2])
[Root Menu] → Basic setup →
Unit
EJX_HART 5[1.2]
DTM
Easy Setup → Unit or
Conguration → Analog Output
→ Unit
Note that the Yokogawa default setting for the
standard temperature is 4°C (39.2°F). For the units
of mmH
2
O, inH
2
O, and ftH
2
O, the pressure varies
according to the standard temperature denition.
Select the appropriate unit with @68degF when a
standard temperature of 20°C (68°F) is required.
Available pressure units are shown below.
inH
2
O@68degF
inHg
ftH
2
O@68degF
mmH
2
O@68degF
mmHg
psi
bar
mbar
g/cm
2
kg/cm
2
Pa
kPa
torr
atm
MPa
inH
2
O
mmH
2
O
ftH
2
O
hPa
- (EJXA, EJAE) 1
- Contents 2
- Revision Information 4
- 1. Introduction 5
- 1.2 Warranty 6
- 1.3 Abbreviation and Marking 7
- 1.5 ATEX Documentation 9
- 2. Connection 10
- IM 01C25T01-06EN 11
- <2. Connection> 13
- 3. Parameter Setting 14
- (next page) 15
- F0301-04.ai 16
- F0301-07.ai 19
- F0301-08.ai 20
- 3.2 Basic Setup 25
- IMPORTANT 25
- 3.2.3 Range Change 26
- 3.2.4 Output Mode 26
- 3.3 Detailed Setup 28
- 3.3.6 Sensor Trim 31
- 3000−3015 32
- Applied Pressure Value 32
- 3.3.7 Trim Analog Output 33
- 3.3.8 External Switch Mode 33
- Hardware Write Protect 34
- 3.3.11 Signal Characterizer 35
- 3.3.12 Alarm 35
- Compensation 37
- Transmitter 38
- 3.3.16 Burst Mode 40
- 1,2 or 3 → Burst Command 42
- 3.3.17 Multidrop Mode 45
- 3.3.17.1 Setting on HART 5 45
- 4. Diagnostics 48
- 4.2 Advanced Diagnostics 50
- (Only for EJX series) 50
- Pressure Measurement 51
- Level Measurement 51
- Functional block diagram 52
- 4.2.2.1 Blockage Detection 53
- Limit parameter 53
- H/L Blocking Detection 54
- A/B Blocking Detection 54
- <4. Diagnostics> 55
- 4.2.2.3 Operation Parameters 56
- Diag Mode 56
- Diag Period 57
- Diag Supp Count 57
- 4.2.2.4 Operating Procedure 58
- Alarm Status 59
- 4.2.2.10 Tuning 64
- Threshold Value 64
- Sampling Period 65
- ILBD Range Setting 65
- Ratio fDP Compensation 65
- Diag DPComp 65
- 4.2.2.12 ILBD Parameter List 66
- 4.2.3 Heat Trace Monitoring 68
- Conguration Changed Flag 74
- 5. Parameter Summary 79
- Installation 88
- A1.3 Denitions and 90
- Abbreviations 90
- Appendix 2. ILBD Check List 91
- Checklist (2/5) 92
- Checklist (3/5) 93
- Checklist (4/5) 94
- Checklist (5/5) 95
Related products and manuals for Sensors Yokogawa EJA440E
Sensors Yokogawa EJX440A User Manual
(76 pages)
(76 pages)
Sensors Yokogawa EJA438 User Manual
(72 pages)
(72 pages)
Sensors Yokogawa EJA530A User Manual
(67 pages)
(67 pages)
Sensors Yokogawa EJA530E User Manual
(52 pages)
(52 pages)
Sensors Yokogawa EJA115 User Manual
(85 pages)
(85 pages)
Sensors Yokogawa EJX115A User Manual
(55 pages)
(55 pages)
Sensors Yokogawa EJX930A User Manual
(83 pages)
(83 pages)
Sensors Yokogawa EJX930A User Manual
(9 pages)
(9 pages)
Sensors Yokogawa EJX930A User Manual
(103 pages)
(103 pages)
Sensors Yokogawa EJX930A User Manual
(163 pages)
(163 pages)
Sensors Yokogawa EJX930A User Manual
(55 pages)
(55 pages)
Sensors Yokogawa EJX930A User Manual
(175 pages)
(175 pages)
Sensors Yokogawa ADMAG CA User Manual
(10 pages)
(10 pages)
Sensors Yokogawa ADMAG AXW User Manual
(52 pages)
(52 pages)
Sensors Yokogawa AXFA14G/C User Manual
(24 pages)
(24 pages)
Sensors Yokogawa ADMAG CA User Manual
(105 pages)
(105 pages)
Sensors Yokogawa ADMAG AXF User Manual
(13 pages)
(13 pages)
Sensors Yokogawa AXFA14G/C User Manual
(109 pages)
(109 pages)
Sensors Yokogawa ADMAG AXR User Manual
(194 pages)
(194 pages)
Sensors Yokogawa AXFA14G/C User Manual
(76 pages)
(76 pages)
© 2020, manymanuals.com. All rights reserved. | 1.649 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals